The 1729-TA Sliding Thru Axle Adaptor is designed to allow any Park Tool PRS-20, PRS-21 or PRS-23 Repair Stand to accept 12mm and 15mm thru axle wheeled bikes.
Park Tool's Thru Axle Adaptors make it possible to adapt all Park Tool Truing Stands to work with 12mm, 15mm, 20mm, and 25mm thru axle front wheels, as well as Cannondale Lefty wheels (each sold separately). The TS-TA also work with the rear 135mm thru axle hubs in the TS-2.2 and TS-3. The TS-TA when used in the TS-8, TS-25, TS-15, TS-7 or TS-5 will work with all rear thru axle hubs. For thru axle hubs greater than 135 (142, 150, 157, etc.) in the TS-2.2, use the TS-2TA Thru Axle Adaptors (sold separately).
Keep your most commonly used tools close at hand with this clever, multi-function tool holder. The TK-4T was painstakingly designed with pockets and holders for specific tool shapes and sizes as well as some generic storage areas. The Tool Kaddie rotates for easy access and is molded from a durable composite material. - Bench Top Mount sits firmly on any flat surface - Specific slots and holders for 3-way hexes, screwdrivers, P-Handles, pliers/cutters - Generic slots and holders to hold a wide variety of tools and small parts - Mounting location to directly attach HXH-2P or HXH-2T P-Handle Holders (sold separately) - Built-in receiver port for PTH-1 Paper Towel Holder (sold separately)
Keep your most commonly used tools close at hand with this clever, multi-function tool holder. The TK-4 was painstakingly designed with pockets and holders for specific tool shapes and sizes as well as some generic storage areas. The Tool Kaddie rotates for easy access and is molded from a durable composite material. - Stand Mount mounts to any Park Tool Professional Shop Stand (all versions of PRS-2, -3, -4, and -33) - Specific slots and holders for 3-way hexes, screwdrivers, P-Handles, pliers/cutters - Generic slots and holders to hold a wide variety of tools and small parts - Mounting location to directly attach HXH-2P or HXH-2T P-Handle Holders (sold separately) - Built-in receiver port for PTH-1 Paper Towel Holder (sold separately)
Securely holds any of Park's TS-2, TS-2.2, and TS-2.2P Professional Wheel Truing Stands and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
Securely holds the TS-4 Professional Wheel Truing Stand and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
Securely holds the TS-4.2 Professional Wheel Truing Stand and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
The BDT-2 is a go/no-go style gauge designed to help set the proper tension on most belt drive systems and sizes. Also gauges rear cog parallelism and angularity.
Park's Tire Seating Tool is designed to quickly seat the bead on stubborn tires. During inflation some tire beads can slip below the rim edge and become difficult to pull out and align. The PTS-1 comes to the rescue with its non-slip jaws and vinyl-coated handles that provide plenty of leverage for pulling out the tire. Plus, it's adjustable to fit various tire widths.
Precision CNC machined dual-sided aluminum tool for the installation and removal of 12- and 16-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8" drive. - Fits Enduro T47: 16-notch 52.2mm OD cup - Fits Enduro PF30: 16-notch 52.2mm OD cup - Fits Chris King ThreadFit T47: 12-notch 50.4mm OD cup - Fits Chris King ThreadFit 30: 12-notch 50.4mm OD cup
Many bicycles will not shift or track properly because the front and rear wheels are not in line with the frame. If these conditions still exist after wheel and derailleur adjustments, the seat stays, chain stays, and rear drop outs of the frame may be misaligned. For years the accepted method to check the alignment of the rear drop-out was to run a string on either side. This method does work to some extent. However, it is not accurate because the measurement is not taken at the drop-out. With the Park Tool Frame Alignment Gauge, the alignment can be checked quickly and accurately at the drop-out. It includes a retractable pointer to fit all sizes and types of bicycles.
Suspension maintenance and tuning require tools designed for a precise fit. The SKT-6 from Park Tools is a shop-quality set of six flat-faced sockets designed for use with common suspension fork fittings. Ideal for use with Park Tool Torque Wrenches, the 3/8-inch drive sockets are forged from tough chrome vanadium steel and chrome plated for lasting durability. - 24, 26, 27, 28, 30, 32mm flat-faced sockets - All sockets are 3/8" drive - Note: 27mm socket is tapered for better access on Suntour suspension forks
Truing stand upright extensions install in seconds on any TS-2 or TS-2.2 Truing Stand, allowing the stand to be used on wheels with hubs up to 200mm wide (tandem, fat and downhill bikes), as well as on wheels with a 29-inch mountain bike tire installed*. In addition, specially sized bosses serve as adaptors so the stand can be used with wheels using thru-axle hubs with removable axles. Same features as the the TS-2EXT.2 with the addition of slots to secure rear drive e-bike wheels. * Note: TS-2.2 Truing Stand does not require these adaptors to accommodate 29-inch wheels but does require it to fit hub widths from 180mm to 200+mm.
Park Tool's TS-RK is a complete rebuild kit for the TS-2 truing stand. It is complete with the most commonly replaced small parts and the instructions needed to get your stand back into top working condition. In addition to making the stand more accurate and reliable, once installed, the new parts also allow the stand to be readjusted much more easily, should it be thrown out of adjustment. This is a great addition to the older TS-2 stands. If your stand has silver-colored shaft collars, upgrade with the TS-RK. The TS-RK includes the following: • 1 - #211S Main Shaft • 4 - #749-1 Bearing Washer • 2 - #748-1 Needle Bearing • 2 - #209-2 Shaft Adjusting Collar • 1 - #229 Spring • 4 - #232-2 Split Nylon Bushing • 2 - #235-2 Split Nylon Bushing • 1 - #222-SR Right Caliper Spring • 1 - #222-SL Left Caliper Spring • 1 - Set of Installation and Adjustment Instructions
A simple, one position version of our WH-1 Wheel Holder. The WH-2 is a quick and easy solution to securely hold nearly any wheel to make tire, wheel, cassettes and hub work a snap. Can be bolted or clamped to a bench or installed in a bench vise. Includes axles and adaptors to fit 12, 15 and 20mm thru axles as well as quick release and solid axle hubs.
Park's Freewheel Remover Wrench provides superior leverage for freewheel removal and installation. Its head slides over Park freewheel removers and features a locking knob for a secure fit.
Clean out or restore damaged threads in crank arms with Park Tool's Pedal Taps. They're sold as a set of right and left hand threads. Made of high carbon steel, precision ground, and hardened to stay sharp, they cut easily and fit all conventional tap handles. • Includes a set of 2 taps, 9/16" x 20 tpi • Made of high carbon steel, precision ground, and hardened to stay sharp • Fits all conventional tap handles The tap drill size for a 9/16-inch x 20 tpi thread is nominally 33/64-inch.
Park Tool's 750.2 Centering Cone Adaptor increases the size of the centering cone of the HTR-1 and HTR-1B Headtube Reaming and Facing Sets. The 750.2 will allow you to use the HTR-1(B) to ream and face head tubes designed to accept IS, ZS, and 1.5-inch EC headset standards. Before reaming or facing, make sure you have the correct cutting tool and pilot for the headset standard(s) you are using. Please refer to our product pages for cutters and pilots for this detailed compatibility information.
Secure engagement, easy to use, and fast! The CP-1.2 quickly grips cogs from 9 to 24 teeth with no manual adjustments. A great shop tool, the CP-1.2 is 13.7-inches (35cm) long and can be used with one hand to hold any 5-speed to 12-speed road or mountain cassette solidly during lock ring removal. Forged steel construction with a spring loaded return and comfortable dual density grips.
Commonly referred to as a 4th Hand, Park's Cable Stretcher pulls cables tight. Its one-hand operation and thumblock holds the cable so you can easily maintain cable tension while tightening cable fixing bolts and nuts. Made from chrome-plated and heat-treated steel and featuring cushion grips for comfort, the Park Cable Stretcher is a must for any serious mechanic.
The Park Tool SBS-1.2 is a shop-quality set of sockets, hex bits, and Torx style bits, selected specifically for common bike repair needs. Ideal for use with Park Tool torque wrenches, the SBS-1.2 3/8" drive bits and sockets are made from tough, chrome vanadium steel for lasting durability.
Precision CNC machined dual-sided aluminum tool for the installation and removal of 12- and 36-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. Fits Praxis M30 and M35 - M30: 12-notch 48mm OD cup - M35: 36-notch 51.7mm OD cup
In the tradition of our premium quality fold up tools, the BO-4 is a combination corkscrew and bottle opener complete with a knife/foil cutter. This multi-tool folds for storage and features all stainless steel mechanisms housed in a forged aluminum case. This is a top quality beverage tool perfect for the workbench, toolbox or wine bar.
Park Tool's Bottom Bracket Bearing Tool Set removes and installs (with a bearing press which is sold separately) BB86, BB90, BB92 and Press Fit bottom brackets from Shimano, Race Face, SRAM and others that use a nominal 24mm-diameter spindle. This tool has a bearing remover that fits inside the bottom bracket shell and into the bearing so the bearings can be tapped out of the frame with a hammer. The set also includes two bushings that you use in conjunction with a bearing press for precision bearing installation (bearing press sold separately).
A fast and convenient tool to remove and install 12-spline Shimano/SRAM style cassette lockrings, as well as similar lockrings on rotor discs. The FR-5H features a modified FR-5 tool that allows use without removing most quick release skewer nuts. The removable, threaded steel handle makes it possible to replace a worn or damaged head. - Fits Shimano, SRAM (including 1x), SunRace, SunTour, Chris King and other cassette lockrings - Also fits some Shimano disc brake lockrings
Accurately gauge the straightness of disc brake rotors while the wheel is mounted in a TS-2.2 or TS-2 Professional Wheel Truing Stand (each sold separately). Park Tool's Rotor Truing Gauge features an infinitely adjustable, finely threaded indicator gauge. It works with any diameter brake rotor.
$18.95 - $42.95
The MT-10, 20, 30 and 40 are high quality folding take-along tools that feature forged aluminum side plates, a mix of hardened and plated tools, and smooth ergonomic operation.
Park's Oversize Adjustable Saw Guide guides a hacksaw so that you can accurately cut fork steerers, airfoil-shaped seatposts and more. The guide is made to be held in a vise and it has hardened-steel cutting slots and a secure clamp for the part you're cutting so that you make a perfect cut every time. The guide is compatible with round tubes from 1 to 1-3/4 inches in diameter and airfoil shaped parts up to 3.5 inches long. There are slots for standard and carbon-specific saw blades.
Park's Threadless Star Nut Setter makes it quick and easy to install star-fangled nuts used with 1-inch and 1-1/8-inch threadless headset systems. Using a durable steel driver and built-in guide, the TNS-4 perfectly aligns the star-fangled nut and sets it to the proper depth every time. Plus, the unique design virtually eliminates pinched fingers!
Park's Threadless-Fork Saw Guide ensures a straight, accurate cut on threadless forks. Slide on the guide, clamp it down and the hardened-steel cutting slot ensures a perfect cut every time. You can remove as little as 1mm, too.
Park's Threadless-Fork Saw Guide ensures a straight, accurate cut on threadless carbon forks. Specially designed to accommodate wider, carbon specific saw blades, the SG-8 ensures a perfect cut every time. Slide on the guide, clamp it down and the specially shaped hardened-steel cutting slot guides your saw blade. And, the SG-8 Saw Guide ensures a straight, clean cut on fork steerer tubes up to 1-1/4-inches.
Dial Indicator Set bolts directly to the DT-3 allowing for greater accuracy and a way to measure results. Now includes an elongated, cylindrical tip that is large enough to work around voids in most rotors.
Shop quality preset torque driver that limit torque applied to fasteners, preventing over tightening and damage to lightweight components. The PTD-4/PTD-5/PTD-6 feature all metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at our factory in Minnesota. - ¼ inch hex drive - Includes 3, 4, 5mm and T25 bits stored in the handle - Limits torque applied to fasteners while rotating clockwise - All metal internal construction for long life
The BBT-30.4 Bottom Bracket Bearing Tool Set is designed and built to install and remove the bearings used in BB30, PressFit 30 (PF30), 386EVO, BBright and PF121 bottom bracket systems. The BBT-30.4 features a bushing set used in conjunction with a head cup press to quickly and precisely press the BB30 and PF30 bearings in the bottom bracket shell. The included BB30 bearing remover works from inside the shell to easily push out bearings.
The MTC-40 features a super strong, composite, multi-position handle, with hardened and plated tools and smooth ergonomic operation. Lightweight, compact, and perfect to carry along. - 2.5, 3, 4, 5, 6 and 8mm hex wrenches - T25 & T30 Torx compatible driver - Combo cross/straight tip screwdriver - 5- to 12-speed compatible chain tool* - Rotor straightener - CO2 cartridge inflator adaptor - Bottle opener - Key ring holder - Weight: 217g (7.65 ounces) *The MTC-40 chain tool will not peen Campagnolo 11-speed chain rivets (see CT-4.3 or CT-6.3)
Clean out or restore damaged threads in crank arms with Park Tool's Pedal Taps. These taps can be used with either steel or alloy crank arms. The set includes both right- and left-hand threads. The 1/2" size is common on "one-piece" cranks. • Includes a set of 2 taps, 1/2" x 20 tpi • Made of high carbon steel, precision ground, and hardened to stay sharp • Fits all conventional tap handles
A professional quality shop chain tool that works on 5-speed to 12-speed Road and Mountain Bike derailleur chains*, including SRAM AXS 12 speed, as well as 1/8-inch and 3/16-inch chains. The CT-3.3 features an adjustable locating shelf so it works on any width chain to remove and install chain rivets. Built to last and easy to use, the CT-3.3 features a comfortable handle, investment cast steel body and replaceable driving pin (#CTP). *The CT-3.3 will install, but not peen, Campagnolo 11 and 12-speed chain rivets. - Comfortable T-handle - Replaceable driving pin (CTP) - Investment cast steel body - Adjustable locating shelf
Park’s Professional Cable And Housing Cutter is specifically for use on derailleur and brake cables and housing. It even makes quick work of hard-to-cut shift-cable housing. Its cold-forged, heat-treated-steel handles won't bend and its precision-ground jaws cut perfectly every time. Its dual-density molded grips are specially contoured for superior comfort and control. Plus, there’s a built-in cable-end crimper and a forming hole for reforming housing ends.
Park's Screw-Type Chain Tool is the ideal shop tool for easy and reliable chain maintenance and repair. The sliding shelf makes it compatible with 1/8th-inch chains and all 3/32nd-inch chains, from 5- to 11-speed. It's made from investment-cast tool steel and has long vinyl-coated handles and fine threading for easy chain pin removal. It also includes a stiff-link loosener and comes with an extra pin.
Big and powerful, Park's Adjustable Wrench is forged from steel and chrome plated for maximum durability. Its jaws open up to 36mm and the torque-friendly, 12-inch handle is vinyl dipped for comfort.
Keep your work area tidy with Park's Bench Top Small Parts Holder. It's constructed from rugged stainless steel with a clear, acrylic hinged top that lets you see what's inside. It also includes 4 removable bins that are perfectly sized to hold small parts, cable end caps, grease and whatever other little items you can think of.
A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The Chain Gang contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings. The Chain Gang includes: - CM-5.3 Cyclone Chain Scrubber - GSC-1 GearClean Brush - 8 oz. bottle of Bio ChainBrite The CG-2.4 works on nearly any bike, including multi-speed, single-speed, and e-bikes.
A great shop accessory made to hold a wide variety of axles, spindles and any Park Tool Freewheel Remover/Lockring Tool. Made from precision extruded aluminum.
Precision CNC machined aluminum tool for the installation and removal of 16-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. - 16 notch 49mm OD cup - Fits FSA MegaEvo and more
A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The Chain Gang contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings.
The CDG-2 easily and accurately measures bolt circle diameter (BCD) in millimeters for a wide variety of four- and five-bolt chainring patterns. Made of anodized aluminum and permanently laser engraved, the tool centers itself in chainring holes, chainring bolts, or crank arm holes. The CDG-2 also includes a center-to-center distance scale and a handy reference chart listing additional mounting pattern measurements.
The RT-1 Head Cup Remover makes headset cup removal easy. The tool is pulled through the frame until the flared ends snap in behind the cup. A blow on the tool head removes the cup. • Fits 1”, 1-1/8” and 1-1/4” headsets • Strong, heat treated alloy steel with nickel finish The RT-1 will also remove the PressFit 30 (PF30) bottom bracket units. The PressFit 30 inside diameter is the same as headset cups, and are pressed in the same manner. SHIS terminology: Removes cups of EC29, EC30, EC34, EC44, ZS41, and ZS44
The RT-2 Head Cup Remover makes headset cup removal easy. The tool is pulled through the frame until the flared ends snap in behind the cup. A blow on the tool head removes the cup. • Designed for the 1-1/4 inch and 1-1/2 inch headest standards • Also easily removes cups on one-piece cranks • Strong, heat-treated alloy steel with a nickel finish SHIS Terminology: The RT-2 will remove cups of ZS44, ZS49, ZS55, ZS56, EC49 and EC56 headsets.
Park's Professional Pedal Wrench features an angled, oversize head for maximum leverage. It has two 15mm wrenches at different angles, so you can maximize your leverage, and a long, round, vinyl-coated handle that won’t dig into your hand the way flat wrenches do. There's even a hole in the end for hanging the wrench on your toolboard.
The CRS-15EXT includes a tube and fitting to extend any CRS-15 to work on fork steering tubes up to 425mm.
True your wheels right from your bicycle repair stand with Park's Repair Stand-Mounted Wheel-Truing Stand. It's comprised of two parts. One piece is an axle holder for you to securely attach your wheel (accepts all wheel diameters and rim widths) via your quick release or axle nuts. The other piece attaches on the stand near the rim and acts as a pointer that shows where the wheel needs truing. This small, light truing stand installs quickly and easily on Park's PRS-25 and PCS-10 repair stands, and also Park's PCS-1 and PCS-4 stands when they are used with the adjustable-height extension.
• 15mm L-shaped hex wrench to fit Shimano rear thru-axle freehubs • Through-hardened industrial quality steel • Chamfered tips for a precision fit
Precision component screwdriver machined to exact standards to ensure a perfect fit on compatible component fasteners. Featuring an ergonomic, CNC machined and hard anodized 6061 aluminum handle.
Park Tool's Utility Pick Set is a set of three unique, multi-purpose picks ideal for a wide variety of detail work. Features: • Aluminum handle with magnet • Picks are replaceable, cold formed, heat treated and polished high carbon steel • Set includes 1-straight, 1-hook and 1-90 degree pick
To prevent poor shifting and uneven drivetrain wear, most manufacturers recommend chain replacement at or before 1% stretch. Now you can quickly and accurately determine the wear and stretch of any chain with Park's Chain Checker. Simply insert the Chain Checker’s pins into 2 links, press the swingarm gauge tight, and then check the gauge window for an accurate reading!
The 4th edition of the Big Blue Book of Bicycle Repair is updated with the latest information, procedures and techniques and covers everything from minor adjustments to complete overhauls. The BBB-4 features clear, step-by-step instructions, high quality color photos and useful charts and graphs to thoroughly explain and demonstrate hundreds of repairs. Written by one of the world’s leading authorities on bicycle repair and maintenance, Park Tool Director of Education, Calvin Jones, the Big Blue Book is the perfect reference guide for nearly any level mechanic and every bike. New information and topics included in the BBB 4th edition: - 12-speed and 1x drivetrains - Tubeless tires - Disc brakes - Electronic shifting - New wheel building content - Updated headset and bottom bracket standards - Updated torque specifications - Updated troubleshooting tables
Professional quality component hex driver precisely machined to exact standards to ensure a perfect fit on compatible component fasteners. Featuring an ergonomic, CNC machined, perfectly balanced 6061 aluminum handle hard anodized to take the rigors of everyday use.
Park's Folding Chain Tool is a heavy-duty tool-steel shop-quality chain tool that also folds for carrying in your pack or pocket for use on the road and trail. It's compatible with 9-, 10- and 11-speed chains. It also includes a folding peening anvil for Campagnolo 11-speed chains.
Park's I-Beam Mini Fold-Up Hex Wrench/Screwdriver/Torx Set with Chain Tool includes 1.5, 2, 2.5, 3, 4, 5, and 6mm Allen wrenches, a socket 8mm Allen, a regular screwdriver, a T25 Torx tool (for disc-rotor bolts), a tire lever, spoke wrenches and a chain tool. The I-Beam conveniently fits in pockets and packs, too.
Precision CNC machined aluminum tool for the installation and removal of 12-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8" drive. - 46mm 12-notch OD cup - Race Face® Cinch™, Rotor® BSA30, Zipp® Vuma™, Hawk Racing™ BB3086™, and more