Parts & Accessories
$120.00 - $216.00
Freehub bodies for Zipp Cognition hubs.
Zipp Speed Weaponry Freehub Bodies - Material: Aluminum
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Secure - Prevents theft instead of standard 9 mm quick-release skewers Quick Assembly - Use proprietary key on frame dropout Construction - Stainless springs with chromoly axle
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and to perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening
Ritchey Front Hub Conversion Kits
$19.50 - $27.20
DT-Swiss Center Lock Adaptor. Allows 6-bolt rotors to be used on Center Lock hubs. - Rotor thickness between 1.8mm and 2.2mm - Easy assembly and only 29g - Made in Switzerland by DT Swiss - 230mm version accepts all rotors up to 203mm diameter - 160mm version accepts all rotors up to 160mm diameter
$11.25 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
$20.00 - $21.00
Front end cap conversion kits for NoTubes Neo and Neo Ultimate - SealLock end caps feature a low friction U-cup seal that snaps into place
- Extra security against theft - 5mm hex CrMo axle
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm. Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.
- Replacement rear skewer - Spacing: 135mm - Material: Steel
Page 1 of 1